Guides
Short, hands-on explainers. Each one is a single idea with something to press, drag or break. A few minutes each, no experience needed.
- How one wire drives a whole strip of LEDs
No LED on the strip has an address. So how does LED 7 know which color is its?
- Why delay() makes your project ignore you
Press the button. The board with delay() will miss most of your presses.
- Baud rate: why your serial monitor shows garbage
"¾ýÿ¿þ" in your serial monitor is good news: the wiring works, only the speed is wrong.
- The USB cable that looks fine and isn’t
The board lights up, but your laptop can’t see it. It’s probably the cable.
- How many LEDs can USB power?
A ten-LED strip on full white can draw more than a USB port supplies, and the board starts rebooting.
- ESP32-C3 SuperMini pinout, explained
Sixteen pins, a few with surprises. Tap any pin to see what it does.
- Multimeter probes: which jack is which
Black goes in COM. Red goes in V almost every time. The jacks marked A are the ones that blow fuses.
- Continuity: is this wire actually connected?
Touch the probes to both ends of a wire. A beep means it’s connected. Silence means it isn’t.
- Measuring voltage with a multimeter
Check a battery, then the 5V and 3.3 pins on your board. And find out what the minus sign means.
- Measuring current without blowing the fuse
To measure current the meter goes in the circuit, not across it. Put it across a battery and the fuse blows.
- Which solder wire should you buy?
Leaded or lead-free, thick or thin, and the one kind that must never touch a circuit board.
- What temperature should your soldering iron be?
Too cold makes a dull, weak joint. Too hot burns the flux and lifts the pad. Find the window.
- Tin first, then join
Two surfaces already coated in solder flow together in a second. Bare ones fight you.
- Spot the bad solder joint
A good joint looks like a tiny shiny volcano. Can you name what went wrong with the others?
- Why your soldering tip stopped working
A black tip won’t take solder, however hot it is. Here’s how it got that way, and how to keep it shiny.
- Soldering header pins onto the ESP32-C3 SuperMini
Use a breadboard as a jig, tack two opposite corners, and the pins come out straight every time.
- The BOOT and RESET buttons on the ESP32-C3
Hold BOOT, tap RESET, let go of BOOT. It rescues a board that won’t take new code.
- When your ESP32-C3 won’t upload
No port, the wrong port, a busy port, or a board too busy to listen. Answer a few questions and find the fix.
- Where did my Serial output go?
Your code prints, the monitor stays blank. On an ESP32-C3, two missing lines in platformio.ini send it all to pin 21.
- Your first PlatformIO project for the ESP32-C3
A few lines of platformio.ini get you building. Tap each one to see what it does, and what breaks if it’s wrong.
- The pins that can stop your ESP32-C3 from booting
Wire a button to the wrong pin and your board sits waiting for new code instead of running yours.
- Which ESP32-C3 pins are safe to use?
Some pins already have a second job: USB, serial, the flash chip. Pick a job and see which pins are free.
- Reading analog voltages on the ESP32-C3
analogRead() gives a number from 0 to 4095, but it’s noisy and stops being accurate above about 2.5 V.
- Fading an LED with PWM on the ESP32-C3
The pin is only ever on or off. Switch it fast enough and the LED looks dimmed.
- Powering the ESP32-C3 without USB
Batteries, power banks, the 5V pin or the 3.3 pin: which ones are safe, and which one fries the chip?
- WiFi on the ESP32-C3 in 3 minutes
Four lines connect the board to WiFi. Here’s what to do when they don’t.
- Bluetooth LE or WiFi: which do you need?
WiFi reaches the internet. BLE talks to the phone in your hand. Tick what your project needs.
- Bluetooth LE basics: a light switch on your phone
Advertise, connect, then read and write a value. That’s how a phone switches an LED on.
- Why turning on WiFi resets your board
WiFi transmits in bursts of over 300 mA. A thin cable can’t keep up, and the board reboots.
- Deep sleep: make a battery last months
Asleep, the ESP32-C3 chip draws 5 microamps. Awake with WiFi, thousands of times more.
- Updating your ESP32 over WiFi
Once the first upload is done by cable, the next ones can go over WiFi. The board keeps two copies, so a dropped update leaves the old code running.
Workshop guides
Step-by-step companions to our in-person workshops.
- Programming LEDs
Flash an ESP32-C3, light up an LED strip, then change the code and make it do something new.